Journal: Mark W. Jackwood's V8 MGB
 |
Visit Mark W. Jackwood's Profile for more information on this member. Subscribe to this Journal: 
What is RSS?
There are 52 entries in this Journal. Status: Member Location:  Georgia, USA |
|
Rear End Assembly
Created on 2009-10-29 12:07:49
Here is a picture of the rear end with the shock mounts, antitramp bar, and antisway bar. All the bushings on the suspension are the red poly bushings from Energy Suspension.
New thrust washers for the differential gear and pinion were installed along with a new split pin. And the rear end was painted with POR15.
New thrust washers for the differential gear and pinion were installed along with a new split pin. And the rear end was painted with POR15.
Click the thumbnail to view image:
Rear end/shock/antitramp/antisway
Rear end/shock/antitramp/antisway
Sponsored Links. Did you know you can turn advertising off and support this site by upgrading to a Gold Membership?
Summary of Previous Journal Entries
Showing previous 10 journal entries:
| Title | Date | #Pic | #Cmt | Excerpt |
|---|---|---|---|---|
| Preparing To Insert A V8 Entry #1 | 2009-10-29 | 1 | Now the fun begins. Putting it back together. All winter I was cleaning and painting (POR15 of course) parts. Here you can see the clutch and brake master cyl. and brake booster, a... | |
| Truck Bed Liner On The Bottom | 2009-10-29 | 1 | Then I flipped it over and put "brush on" truck bed liner called Raptor on the bottom and the wheel wells. Between the POR15 (see previous entry) and truck bed liner... | |
| Disassembly And Paint | 2009-10-29 | 1 | Once all the body modifications were made, the car was completely disassembled and painted inside with Por15. The engine bay and interior including the boot was painted gray, and b... | |
| Roll Bar Backing Plates | 2009-10-29 | 1 | One of the backing plates for the roll bar consisted of this angle iron to improve body stiffness. | |
| Roll Bar | 2009-10-29 | 1 | I know some don't like them but roll bars don't bother me aesthetically and this being a V8 conversion I wanted to try to add some stiffening to the body. All of the mounting point... | |
| Mazda Miata Seats | 2009-10-29 | 1 | Leather Mazda Miata seats were fitted. The original mounting points were used for the front bolts and two new holes were drilled for the rear. In addition, backing plates under the... | |
| Tramp Bars Mounting Points | 2009-10-29 | 1 | Glen Towery's mounting brackets were used for the tramp bars. The fine thread bolt allows precise adjustment of the tramp bars. I did not use a panhard rod. The tra... | |
| Tramp Bars | 2009-10-29 | 1 | To keep the stock MGB rear end located and put power to the ground adjustable tramp bars were made. Glen Towery's tramp bars were modified by cutting them, welding a nut on to the ... | |
| Header And More Stuff | 2009-10-29 | 1 | RV8 style headers were ceramic coated inside and out by Jet-Hot to increase longevity and decrease temperatures in the engine bay. Ceramic coating was expensive should pay for its ... | |
| Headers And Stuff | 2009-10-29 | 1 | A reinforcing ring was made from some sheet metal and a lot of manipulation with a hammer to strengthen the fender where the headers will pass through. |
The contents of this journal entry (including entry images) are released
under the terms of the Creative Commons License unless otherwise noted.
under the terms of the Creative Commons License unless otherwise noted.
This page last modified May 09 2009 16:07:49 pm
Add a comment to this journal entry:
Please sign in if you already have an account or register now to enable this feature.