Journal: Wilbur Engelsma's Journal
 |
Visit Wilbur Engelsma's Profile for more information on this member. Subscribe to this Journal: 
What is RSS?
There are 51 entries in this Journal. Status: Silver Member  Location:  Broomfield, CO, USA |
|
Trunk Supports
Created on 2007-11-22 10:07:19
I installed a pair of hydraulic trunk supports to replace the existing trunk support. Like usual I didn't read the instructions first and installed (welded) the new one parallel to the existing one. So naturally, the trunk wouldn't close (I didn't install the extra piece to the existing bracket to move the pivot point). So I had to cut the new bracket off and rewelded it in the correct location, and install the missing piece. The end result works really well, no excessive force required to open or close the trunk.
Click the thumbnail to view image:
right side
left side
don't forget this piece!
right side
left side
don't forget this piece!
Sponsored Links. Did you know you can turn advertising off and support this site by upgrading to a Gold Membership?
Summary of Previous Journal Entries
Showing previous 10 journal entries:
| Title | Date | #Pic | #Cmt | Excerpt |
|---|---|---|---|---|
| Leaf Spring Hanger Braces | 2007-11-13 | 4 | The leaf spring hangers are just welded to the floor at the corners, so I thought I would reinforce them. This is not totally my idea- I found a similar installation for a 3 link s... | |
| Gearing | 2007-11-13 | Since there is a lot of discussion on the V8 board about rear end ratios, I have done some research and calculations on the vehicle my motor/trans came from as well as the stock MG... | ||
| Seat Installation | 2007-11-01 | 4 | I have read a few postings about installing the Fiero seats in MGBs, and want to make sure these go in essy. I'm doing all the mods prior to recovering the seats, just in case ther... | |
| Seats | 2007-11-01 | 3 | Although the seats that came with the were way cool (two tone diamond tuck), I am replacing them with a set of Fiero seats. The seats I found are pretty trashed, but since I will b... | |
| Kick Panel Speakers | 2007-10-20 | 8 | Now that the existing holes in the kick panels are patched, it's time to cut holes in them. I have 4 Soundstream Reference speaker systems to install in the car (2 front, 2 rear), ... | |
| Tail Lights | 2007-09-12 | 6 | 3 | Since I filled in the backup light holes in the rear panel, I need to add backup lights somewhere to keep things legal. I found some info that others had put them in the tail light... |
| Fuel Tank Modifications | 2007-08-12 | 6 | I've started modifying the fuel tank. First I sealed up the existing filler tube, vent tube and the sender opening by welding a patch over each spot. I have a filler tube f... | |
| Gas Tank Internals | 2007-07-23 | 6 | I found a Datsun Roadster website where the SR20DET and other fuel injected conversions are explored at length, and found information on converting the fuel tank to an internal sum... | |
| Gas Tank | 2007-07-20 | 3 | Since I am replacing the old gas tank I thought I would cut the old one apart and see what baffles are in the stock tank. Also, I'm curious what the inside looks like after 35 year... | |
| Speaker Cutout Repair | 2007-07-16 | 5 | The previous owner had cut a couple jagged holes for 6X9 speakers in the inner kick panels. These allowed moisture into the interior and destroyed the speakers that were installed ... |
The contents of this journal entry (including entry images) are released
under the terms of the Creative Commons License unless otherwise noted.
under the terms of the Creative Commons License unless otherwise noted.
This page last modified December 01 2007 20:50:32 pm
Add a comment to this journal entry:
Please sign in if you already have an account or register now to enable this feature.