Journal: Wilbur Engelsma's Journal
 |
Visit Wilbur Engelsma's Profile for more information on this member. Subscribe to this Journal: 
What is RSS?
There are 51 entries in this Journal. Status: Silver Member  Location:  Broomfield, CO, USA |
|
Mirrors
Created on 2008-08-03 18:22:55
I don't mind the look of the stock mirrors, but they do leave a bit to be desired as far as viewing area. So I have been looking for alternatives. The current options are:
RX7: electric adjust, reasonable size, but kind of boxy/angular looking.
Miata: electric adjust, nice shape, but the mounting surface angle is incorrect.
3000GT: electric adjust, heated, correct mounting angle, too large
All of these options would offer electric adjustment, but will require reinforcing the door skin to prevent buckling. And the just don't look "right". I saw a couple cars with Harley Motorcycle mirrors. These have possibility- the are convex so they have a larger viewing area, nice chrome finish, and are mounted to the wind wing frame instead of the door skin, so the doors would be much cleaner.
RX7: electric adjust, reasonable size, but kind of boxy/angular looking.
Miata: electric adjust, nice shape, but the mounting surface angle is incorrect.
3000GT: electric adjust, heated, correct mounting angle, too large
All of these options would offer electric adjustment, but will require reinforcing the door skin to prevent buckling. And the just don't look "right". I saw a couple cars with Harley Motorcycle mirrors. These have possibility- the are convex so they have a larger viewing area, nice chrome finish, and are mounted to the wind wing frame instead of the door skin, so the doors would be much cleaner.
Click the thumbnail to view image:
RX7 Mirrors
3000GT Mirrors
Harley mirror installed (not my car- this one is finished)
size comparison- Harley - RX7 - Miata - 3000GT
MGB vs Harley mirror comparison
RX7 Mirrors
3000GT Mirrors
Harley mirror installed (not my car- this one is finished)
size comparison- Harley - RX7 - Miata - 3000GT
MGB vs Harley mirror comparison
Sponsored Links. Did you know you can turn advertising off and support this site by upgrading to a Gold Membership?
Summary of Previous Journal Entries
Showing previous 10 journal entries:
| Title | Date | #Pic | #Cmt | Excerpt |
|---|---|---|---|---|
| Trunk Lid Fit | 2008-08-03 | 3 | The trunk lid also didn't fit quite right- zero gap at one point and non-flush surfaces at a couple more areas. So back with the hammer, grinder and filler. Now it all fits correct... | |
| Tail Lights | 2008-07-20 | 3 | The sheet metal around the tail lights didn't fit too well either- large gaps and the light frames don't sit flush to the body all around. After I filled and blended, the lights no... | |
| Door Seams | 2008-07-06 | 6 | After all the body panels were installed and the doors hung, I measured the gaps around the doors. They varied from approximately 1/8" to 3/8", and the door skins weren't flush to ... | |
| Door Openings | 2008-07-02 | 5 | Since things are already getting out of hand welding up all the body seams, I thought I would seal up the gap between the front fender and the inner fender (at the front edge of th... | |
| Front Left Fender Completed | 2008-02-23 | 3 | Whoo-hoo! I finished blending in the front left fender this weekend, and primed it after finishing. Things are starting to come together! | |
| Fender Vents | 2008-02-12 | 6 | To keep the heat down in the engine compartment, I am installing vents in the fenders. I like the portholes (ventiports) from the 61 Buicks, and after much searching, I have enough... | |
| Right Front Fender | 2008-02-10 | 6 | Even though I didn't have to replace the whole right rocker panel, the front area had some damage that had to be patched prior to replacing the fender. The right fender needed repa... | |
| Left Front Fender | 2008-02-03 | 6 | Time to start on the front end bodywork. I have patch panels for both sides to replace the piece behind the front wheel from the chrome strip down. Plus the front corner where the ... | |
| Fuel Tank Mods Continued | 2008-01-12 | 9 | I didn't get to work on the car over Christmas, but since I got to spend time with kids home from college, that was OK. Now that everyone is back where they belong, and the world... | |
| Parking Brake | 2007-11-24 | 4 | 2 | I have never liked the location of the parking brake lever for three reasons: 1. The interference with the Fiero seats I am installing 2. The cable location in the tu... |
The contents of this journal entry (including entry images) are released
under the terms of the Creative Commons License unless otherwise noted.
under the terms of the Creative Commons License unless otherwise noted.
This page last modified December 01 2007 20:50:32 pm
Add a comment to this journal entry:
Please sign in if you already have an account or register now to enable this feature.