Journal: Wilbur Engelsma's Journal
 |
Visit Wilbur Engelsma's Profile for more information on this member. Subscribe to this Journal: 
What is RSS?
There are 51 entries in this Journal. Status: Silver Member  Location:  Broomfield, CO, USA |
|
New Motor Mounts
Created on 2008-09-07 20:59:42
The motor mounts were purchased from Michael Spreadbury, who installs SR20 motors in Datsun Roadsters. He has some very impressive installations, and fabricates and sells some of the custom parts necessary for the installation. I needed to make some modifications to use his motor mounts, but they are beautiful parts.
Click the thumbnail to view image:
right motor mount
right motor mount
left motor mount
left motor mount
right motor mount
right motor mount
left motor mount
left motor mount
Sponsored Links. Did you know you can turn advertising off and support this site by upgrading to a Gold Membership?
Summary of Previous Journal Entries
Showing previous 10 journal entries:
| Title | Date | #Pic | #Cmt | Excerpt |
|---|---|---|---|---|
| Engine Repositioning | 2008-09-07 | 6 | I measured the position and angle of the engine. and found that it was offset by about 1/2" and the angle was incorrect (should be 5 degrees toward the left side). I was also conce... | |
| Electrical Conduit | 2008-09-01 | 4 | I added a conduit to the front wheel well on both sides to run the wiring as well as the hood latch release through. This should keep the engine compartment free of extraneous wiri... | |
| New Toy | 2008-09-01 | 1 | After trying to figure out how to make some of the firewall cuts I need to make, I decided to buy a plasma cutter. Just a cheap one (yeah Harbor Freight), but this really makes cut... | |
| Hood Repaired | 2008-09-01 | 2 | The last piece of sheetmetal to be worked on is the hood. There were two punched in areas close to the bulkhead end, and the front lip was also damaged. The hood is now repaired, a... | |
| Hood (bonnet) Seams | 2008-08-24 | 3 | Since I welded the fenders on, I removed all the bolts and captive nuts that hold the fender in place along the hood edge. The bolt holes were welded in, then ground flush and fill... | |
| Doors | 2008-08-23 | 2 | More body mods: Since I am using Harley mirrors that mount to the wind wing, I welded up the mirror holes in the door. I also welded in the door lock hole. Doors are now ni... | |
| 4-link | 2008-08-11 | 2 | My Guzman 4-link arrived today- SWEET! I hope I can get to install it this weekend. | |
| Mirrors | 2008-08-03 | 5 | I don't mind the look of the stock mirrors, but they do leave a bit to be desired as far as viewing area. So I have been looking for alternatives. The current options are: R... | |
| Trunk Lid Fit | 2008-08-03 | 3 | The trunk lid also didn't fit quite right- zero gap at one point and non-flush surfaces at a couple more areas. So back with the hammer, grinder and filler. Now it all fits correct... | |
| Tail Lights | 2008-07-20 | 3 | The sheet metal around the tail lights didn't fit too well either- large gaps and the light frames don't sit flush to the body all around. After I filled and blended, the lights no... |
The contents of this journal entry (including entry images) are released
under the terms of the Creative Commons License unless otherwise noted.
under the terms of the Creative Commons License unless otherwise noted.
This page last modified December 01 2007 20:50:32 pm
Add a comment to this journal entry:
Please sign in if you already have an account or register now to enable this feature.